How do you mix Amerlock 2?
Application Procedure
- Flush all equipment with thinner or Amercoat 12 before use.
- Stir resin and cure using an explosion-proof powermixer to disperse pigments.
- Add cure to resin.
- Do not mix more material than can be used within the expected pot life.
What is Amerlock 2?
Amerlock 2 is a fast-drying, surface-tolerant, VOC-compliant two part epoxy. (mixed 1:1) It has a low-temperature cure (down to 0F), dries to touch in two hours, and can be recoated in three hours. Temperature resistance to 450°F on insulated or uninsulated surfaces when mixed with Amercoat 880 glass flake additive.
What is Amerlock?
Amerlock is the high-solids (85%), high-build epoxy protective coating that provides the solution to maintenance painting in tough industrial, marine and offshore environments around the world.
How do you mix amercoat 450h?
Mixing ratio (by volume) 4 parts resin to 1 part cure Surface temperatures must be at least 5°F (3°C) above dew point to prevent condensation. *Surface must be dry and free of all contaminants.
What is amercoat 450H used for?
Amercoat 450H can be used as a finish coat where attractive appearance and a wide range of corrosive resistance is required. *Certain colors (especially yellow, red and orange) may require additional coats to achieve adequate hiding, particularly when applied over dark or contrasting primer color.
What is amercoat used for?
Amercoat® products provide the confidence of heavy duty protection against chemical contact, corrosion, abrasion, and impact damage in the harshest of end use environments.
How do you mix amercoat 450H?
How do you mix amercoat 68hs?
Mixing Ratio 4 Parts Base to 1 part Hardener by volume. Thinners Thin up to 10% by volume using THINNER 737. Use THINNER 304 for clean up. Equipment The following is a guide; suitable equipment from other manufacturers may be used.
What is epoxy zinc rich primer?
Epoxy zinc rich primers belong to the family of zinc rich coatings that are applied to protect ferrous surfaces from corrosion. These primarily work as sacrificial cathodic protection products.
What is zinc rich primer?
Zinc rich primers are used to protect steel surfaces from corrosion. Unlike regular paints or epoxies which resist corrosion by forming an impermeable barrier between the metal and atmospheric moisture, zinc rich primers provide corrosion protection by electrical means.
What is zinc epoxy?
Zinc Rich Epoxy Primer is a high solids two component epoxy-polyamide zinc rich primer. It contains 90%, by weight, of zinc in the dried film. This product is formulated to meet the corrosion requirements of MIL-PRF-32550 and MIL-DTL-53072. This product may be used with Chemical Agent Resistant Coatings (CARC).
What is epoxy polyamide?
A polyamide in an epoxy is essentially an organic compound very similar to ammonia, but has had one of its hydrogen atoms replaced with another atom. A polyamide epoxy is commonly used as a coating or an adhesive.
What kind of cure does amerlock 2 have?
Amerlock 2 is a fast-drying, surface-tolerant, VOC-compliant two part epoxy. (mixed 1:1) It has a low-temperature cure (down to 0F), dries to touch in two hours, and can be recoated in three hours. It offers exceptional corrosion protection in industrial and marine corrosive environments.
What can amerlock 2 VOC be used for?
As a maintenance coating, Amerlock 2 VOC protects steel structures in industrial facilities: • water towers and other exposures. Amerlock 2 VOC’s has good chemical resistance to splash/spillage, fumes and immersionin neutral, fresh and saltwater (see resistance table). For a complete product data sheet and MSDSs please contact us.
What is the solvent level of amerlock 2Al?
Amerlock 2AL 85% ±3% Amerlock 2’s low solvent level meets most VOC requirements, reduces the chances for film pinholing and solvent entrapment at the substrate-coating interface, often a major cause of coating failure with conventional epoxies and lower solids systems.
When to use amerlock 2 over dry surfaces?
Abrasive blasting is usually the most effective and economical method.When this is impossible or impractical, Amerlock 2 can be applied over mechanically cleaned surfaces. All surfaces must be clean, dry and free of all contaminants, including salt deposits.
