What is axle to crown length?

Axle-to-Crown Length is the more common method of specifying fork length on modern bikes, measured in a direct line from the fork crown to the axle. For suspension bikes, this length can be either: “Unsagged” Axle-to-Crown of the full, uncompressed fork length.

How much travel does a Fox 38 have?

The Fox 38 is the biggest single-crown fork Fox has ever made, with its 38 mm stanchions slotting it in between the Fox 36 and their dual-crown 40. With a minimum of 160 mm travel (and a max of 180 mm), it’s mostly going to be found on longer-travel Enduro sleds.

How much is a Fox 38?

$1,249.00. FOX 38 E-Optimized Factory Suspension Fork – 27.5″, 180 mm, 15QR x 110 mm, 44mm Offset, Shiny Black, GRIP 2.

How do I increase travel on Fox 36?

2018 36mm FLOAT forks can be travel adjusted by replacing the air shaft assembly. 36mm FLOAT NA2 forks can be reduced in travel as low as 100mm (831 air shaft). Certain 36mm FLOAT forks may have their tavel extended only if they were built with a damper that can be extended safely to the new longer travel.

How do you measure axle for crown height?

Measure from the top of the crown (bottom of Headset race), behind the Arch on the lowers, and to the center of the backside of the Axle. This should give you a measurement accurate within a couple millimeters.

What does axle to crown mean?

The axle to crown length of the fork, as you might guess, is the distance between the axle (center of the dropouts) and the crown (where the bottom race of the headset rests). Typical axle to crown lengths for 26” trials forks range from 395mm to 420mm while 20” forks usually measure between 360mm and 390mm.

What’s the difference between Fox 36 and Fox 38?

The names say everything: The Fox 36 has 36mm diameter stanchions and the Fox 38 has, you guessed it, 38mm diameter stanchions. Also the 38 has an elliptical steer tube with more material on the front and rear of the inside of the steer tube, whereas the 36 has a standard round steer tube.

Do I need volume spacers?

In a few words, if you’re bottoming out frequently, but your sag is correctly set, add a volume spacer to reduce air chamber volume and increase the rate of progression in your suspension. Reducing volume makes your suspension firmer sooner in the travel, increasing the spring rate in the mid and end-stroke.

What does increasing axle to crown length do?

It raises the front end and in doing so slackens the head angle. The rule of thumb is for every 20mm of additional AC length you slacken the head angle by one degree. So you have effectively changed the head angle in the above example by 2 degrees.

How do you measure the axle to crown on a bike fork?

How does Fox 38 single crown fork work?

A pinch bolt axle system returns to single crowns to help align the lower legs and reduce running friction. The air spring of the 38 is a bit different to the rest of Fox’s single crown forks, with it using an inner tube inside the fork stanchion, which then uses a smaller diameter piston than the 38mm diameter leg would suggest.

How big is a Fox 32 step cast fork?

Fox Factory Inc. uses cookies to improve your browsing experience on our website. By continuing to browse our website, you give consent for cookies to be used. Starting at 2.98 pounds, the 32 Step-Cast (SC) fork is our lightest cross-country fork ever.

What should the top of upper tube be on a Fox 29?

WARNING: The Pre-2021 FOX 29 in. 40 mm upper tube position is factory-set to safely clear a bottomed-out 2.50 in. tire. Standard “top of the crown” to “top of upper tube” position is 137.00 mm. Never increase “top of the crown” to “top of upper tube” measurement beyond 137.00 mm (A).

What’s the difference between a Fox 36 and 38?

Fork dimensions are easily available through the Fox Tech Help page on their website. But compared to the same travel 36 from 2021 you’re looking at a 3mm longer axle to crown. And compared to a 2020 36 it’s 7mm longer. Bleed valves in the back of the lowers purge built up air and also act as two of the mount points for the 38 specific fender.